The Story

Rotted Rear Door and Sill Replaced in Culver City

An old rear door in Culver City leaked and stuck; under its threshold the wood sill was rotted. The old door and frame came out, the rot was cut away, and a new Masonite half-lite steel prehung door went in with a Kwikset keypad lock.

More from Culver City: window replacement work in Culver City and all our Culver City services.

SL
Shiran Levy

Licensed General Contractor · CA #1131088 · Founder, Buildda Inc.

Warning Signs We Look For

  • A door that sticks or rubs, even after the hinges are tightened
  • Daylight or a draft around the edges when it is closed
  • Soft, dark or stained wood at the bottom of the frame or the sill
  • A lock that no longer lines up with the strike plate

Seeing These Signs at Your House?

Text us about your door

Or call (310) 266-5744, Monday to Saturday.

Materials and where they came from

Verify our CSLB license #1131088

1

Step 1 of 4

Before

This Culver City rear door stuck, its threshold leaked, and the bottom of the frame had gone soft. It sat behind an old metal security gate.

Before: the old rear door behind its metal security gate. It stuck, and the threshold leaked.
2

Step 2 of 4

What We Found

With the gate and the old door out, the cause showed: under the old threshold, the wood sill was rotted. Water had been getting under the door for a long time.

Rot like this is why a door that looks fine from the outside can still leak, stick or let air in. The sill is the first thing water reaches, and once it softens, the frame above it starts to move. With the frame and sill rotted, a prehung door in its own new frame is the cleaner fix.

Under the old threshold, the wood sill was rotted soft and dark.
The old sill, cut away. The dark wood is where water sat for years.

Text us about your project

Is your door soft or dark at the bottom? Text us what you see, and a photo if you have one.

3

Step 3 of 4

The Work

The security gate came off first.

Then the old door came out with its frame, and the floor inside was covered with a drop cloth.

We cut out the rotted wood and cleaned the opening. The Masonite installation instructions ask for a clean, level, solid base and a rough opening about 3/4 inch wider and 1/2 inch taller than the door frame.

The security gate comes off first.
Then the old door and its frame come out together.
The rotted wood cut out, the opening cleaned, the inside protected.

Before the door goes in, the base is checked for level, and three beads of caulk go across the floor under the sill, so water cannot get under it again.

The sill goes into the opening first, then the door tips up into place. We kept it square and plumb, with an even gap around the slab.

The base checked for level before the new door goes in.
The new prehung door set into the opening, square and plumb.

Shims go behind the jambs at the hinges and the lock, with an even 1/8 inch gap around the door and long screws through the hinge side into the framing. Then the gap around the frame gets low pressure foam, never expanding foam, which can bend the jambs.

The new wood casing goes on outside, and the corners, the sill and the trim get caulked.

The casing came from Anderson Moulding Doors and Windows in Culver City.

Shims at the hinges and the lock, long screws into the framing.
Preparing the new wood trim for the outside.
The wood casing, picked up at Anderson Moulding in Culver City.

Text us about your project

Thinking about a new exterior door? Text us what you have in mind, and a photo of the door if you have one.

4

Step 4 of 4

After

The new door is a Masonite half-lite primed steel prehung door from Home Depot, with a vent lite in the top half that opens for fresh air, a Kwikset Halo keypad deadbolt and a matching knob (Kwikset Halo support). A paper test closes the door on a sheet of paper over the threshold: it should slide out with a little tension.

After: the new half-lite steel door with its keypad lock.

The door comes primed, not painted. Masonite asks that the door, frame and trim be painted within 45 days to protect the finish. Once a year, check the caulk at the corners and the sill. Every step, with the products and the maker's instructions, is in our exterior door installation guide.

The care card that comes with the door: paint it within 45 days.

See Our Work

Replacing a Rotted Rear Door and Sill in Culver City

Replacing a Rotted Rear Door and Sill in Culver City

Culver City, CA

The rotted old jamb and sill out, the opening cleaned and leveled, a new Masonite half-lite steel door and a Kwikset keypad lock.

New Concrete Driveway, Demo to Broom Finish

Culver City, CA

Old asphalt out, sidewalk cut for the new drain, city signed off

Trim Primer Ready for Paint | Sherwin-Williams Emerald

Culver City, CA

Priming repaired trim and fascia boards with Sherwin-Williams Emerald primer after replacing termite-damaged wood on a Culver City home.

Ask us directly

Have a question about your own door? Text it to us, and add a photo if you have one.

Frequently Asked Questions

How long does an exterior door replacement take?

It depends on what the old door is hiding. On this Culver City rear door, the security gate and the old door came out, the rotted wood under the sill was cut out and the base made level, then the new prehung door went in and the keypad lock was installed. A door whose frame and sill are sound goes faster, because only the slab is replaced.

Can you replace just the door and keep the frame?

Sometimes. When the frame and the sill are sound, a new slab can be fitted into the old frame. When the frame or the sill is rotted, as it was on this rear door, a prehung door is the cleaner fix: it comes already hung in its own new frame with its own sill, so everything that seals the opening is new.

Do I need a permit to replace an exterior door?

It depends on the city and on whether the opening changes size. A door replaced in the same opening is often treated differently from one that is made wider or moved. Tell us about your door and your city, and we check that city's rules for your job before any work starts.

What is a half-lite door?

A half-lite door has glass in its top half and solid panels below. The door on this job is a vent lite: part of the glass opens for fresh air, which suits a back door that leads to a yard. The steel door comes primed, and Masonite asks that it be painted within 45 days of installation.

Text us about your project to get started

Text us about your door, and add a photo if you have one. A real person on our team replies.

Ready to Start a Project Like This One?

Text us what you need, and a photo if you have one. A real person on our team replies.